China Top Grade Quality DC Solar Water Pump Price (5 Years Warranty)
Solar panels convert sunlight into electrical energy which is passed to the solar pump controller. This energy powers the pump. The Solar Controller/Inverter stabilizes the power voltage and outputs it to drive the electric motor of the pump. If backup batteries (optional) are available, the pump controller can charge them. Batteries store additional energy that can be used later when sunlight may not be sufficient to drive the pump. Water Level Detector/Sensors connect to the controller and protect the pump from running dry, as well as automatically turn it off when a water tank is full.
SPECIFICATION
1. Max Head: 20 -- 320m;
2. Max Flow: 0.76 -- 200 m³/hr;
3. Power: 0.1hp -- 100hp;
4. Voltage: 12 V -120V; 220V -540V
5. Motor: DC motor & AC motor;
6. Material: SS304 & SS316 ;
7. Controller: MPPT type for Automatic Restart;
APPLICATION
1. Irrigation of agriculture
2. Drinking water and living water
3. Garden irrigation
4. Fountains
FEATURES
1. Efficiency improved by 25% with permanent magnetism, direct current, brushless, non-sensor motor.
2. Double plastic package for rotor and stator, motor insulation ≥300MΩ, greatly improving motor safety.
3. High-tech products using MPPT and DSP chip technology.
4. 100% copper wire, cold-rolled silicon steel sheet.
5. Stainless steel 304 & 316 shaft, motor body, screw.
NEW DEVELOPED SOLAR PUMP
1. Restart: Totally automatic restart every morning or when the sun appears after clouds.
2. Efficiency: 15-20% higher than common controllers.
3. Protection Against Wrong Connection: Can protect against being burned if customers reverse panel "+" and "-" terminals during connection.
4. High Temperature Resistance: Can operate well under 50 degrees condition for 24 hours continuous working.
3' Submersible Solar Pump (Screw Pump)
| Model | Voltage (V) | Power (Kw) | Max. Flow (M³/H) | Max. Head (m) | Outlet (Inch) | Diameter* Length (mm) | Weight (Kg) |
| 3SPS0.72/20-D12/80 | 12--26 | 45-150 | 0.72 | 20 | G0.75" | Â | 6.5 |
| 3SPS0.76/28-D12/120 | 12--26 | 120 | 0.76 | 28 | G0.75" | Â | 6.7 |
| 3SPS0.86/38-D12/150 | 12--26 | 150 | 0.86 | 38 | G0.75" | Â | 6.8 |
| 3SPS1.0/30-D24/80 | 16-36 | 45-150 | 1 | 30 | G0.75" | 76*400 | 7 |
| 3SPS1.3/50-D24/140 | 16-36 | 80-200 | 1.3 | 50 | G0.75" | Â | 7.2 |
| 3SPS1.8/80-D24/210 | 16-36 | 100-270 | 1.8 | 80 | G0.75" | Â | 7.5 |
| 3SPS1.8/100-D36/270 | 24-48 | 140-350 | 1.8 | 100 | G0.75" | Â | 8 |
| 3SPS1.8/120-D36/500 | 24-48 | 320-800 | 1.8 | 120 | G0.75" | Â | 9 |
| 3SPS2.3/140-D48/750 | 36-72 | 480-950 | 2.3 | 140 | G0.75" | 76*460 | 9 |
| 3SPS2.3/160-D72/1000 | 48-96 | 600-1200 | 2.3 | 160 | G0.75" | Â | 9.5 |
| 3SPS2.3/180-D72/1300 | 72-144 | 800-1500 | 2.3 | 180 | G0.75" | Â | 9.5 |
| Model | Voltage(V) | Power(W) | Max. Flow (M³/H) | Max. Head (m) | Outlet (Inch) | Diameter* Length(mm) | Weight (Kg) |
| 4SPSC5.0/28-D24/250 | 18-26 | 120-360 | 5 | 28 | G1.25" | 100*540 | 12 |
| 4SPSC5.5/38-D36/400 | 24-48 | 200-500 | 5.5 | 38 | G1.25" | 100*650 | 12.5 |
| 4SPSC5.5/58-D48/750 | 36-72 | 450-900 | 5.5 | 58 | G1.25" | 100*680 | 13.5 |
| 4SPSc6.0/72-D72/1000 | 48-96 | 600-1200 | 6 | 72 | G1.25" | 100*740 | 15.5 |
| 4SPSc6.5/98-D72/1300 | 72-144 | 800-1500 | 6.5 | 98 | G1.25" | 100*880 | 16.5 |
| 4SPSC10/30-D48/750 | 36-72 | 450-900 | 10 | 30 | G1.5" | 100*540 | 13.5 |
| 4SPSC10/44-D72/1000 | 48-96 | 600-1200 | 10 | 44 | G1.5" | 100*650 | 15 |
| 4SPSC10/57-D72/1300 | 72-144 | 800-1500 | 10 | 57 | G1.5" | 100*680 | 15.5 |
| 4SPSC15/21-D72/1000 | 48-96 | 600-1200 | 15 | 21 | G2" | 100*540 | 13.5 |
| 4SPSC15/28-D72/1300 | 72-144 | 800-1500 | 15 | 28 | G2" | 100*620 | 14 |
| Model | Impeller Material | Voltage (V) | Power (KW) | Max. Flow (M³/H) | Max. Head (m) | Outlet (Inch) | Diameter* Length (mm) | Weight (Kg) |
| 6SPSC23/21-D72/1300 | Stainless Steel 304 | 72-144 | 800-1500 | 23 | 21 | G3" | 125*700 | 23 |
| 6SPSC28/13-D72/1300 | 72-144 | 800-1500 | 28 | 13 | G3" | 125*710 | 24 | |
| 6SPSC46/7-D72/1300 | 72-144 | 800-1500 | 46 | 7 | G4" | 125*690 | 22 |
NEW SOLAR PUMP CONTROLLER SPECIFICATION
| ITEM | Controller Voltage | Best Working Voltage (vmp range) | Max limited Voltage (max.Voc) |
| New MPPT Controller | 24V | 17-40V | 50V |
| 36V | 23-50V | 68V | |
| 48V | 32-63V | 78V | |
| 72V | 48-96V | 120V |
NEW MPPT SOLAR PUMP ADVANTAGE :
| Â | New MPPT Controller | Â | Poor Quality Controller on Market |
| Restart | Totally Automatically restart every morning, or when the sun appears after cloud | V.S . | Not steady, and cannot restart automatically |
| Efficiency | 15-20% higher than common Controller | V.S . | Lower efficiency |
| MPPT Function | Has MPPT function | V.S . | No MPPT |
| Input Voltage Range | Increases much larger input voltage range to 150V. Will make the panel selection very easy, also avoid too higher input voltage burn the controller | V.S . | Very smaller input voltage range, largest only to 85V, and will be burnt if the panel voltage increases during the very shining daytime; |
| Protection Against Wrong Connection | Can protect against being burned, in case some customers reversed panel "+" and "-" terminals when connecting to controller; | V.S . | No protection, will be burned definitely |
| High Temperature Resistance | Can run well under 50 degrees condition for 24 hours continually; | V.S . | Will be burned, if temperature more than 40 degrees; |
| Operation | Very convenient to open the box to change the SPEED SWITCH; | V.S . | Not convenient, needs Screwdriver to open the 4 bolts every time; |
| Warranty | 3 Years | V.S . | No warranty or longest as 1 year; |
Extrusion aluminum die and matrix are essential components in the extrusion process of aluminum profiles. The die is a specialized tool that shapes the Aluminum Profile by forcing it through a small opening, while the matrix is the supporting component that holds the die in place and guides the aluminum profile through the extrusion process.The extrusion die is typically made of high-quality steel and is custom-designed to produce the desired shape and size of the aluminum profile. The die is carefully machined to ensure that the extruded aluminum profile is precise and accurate. It is also heat-treated to withstand the high temperatures and pressures of the extrusion process.The matrix, on the other hand, is made of steel and is designed to support the die and hold it in place during the extrusion process. The matrix is also responsible for guiding the aluminum profile through the extrusion process, ensuring that it maintains its shape and size.Both the extrusion die and matrix are critical components in the extrusion process, and their quality and precision can significantly impact the quality of the final aluminum profile. Therefore, it is essential to use high-quality materials and ensure that they are properly designed and manufactured to produce the desired results.
Extrusion Die And Matrix,Extrusion Die Matrix,Aluminum Extrusion Die Mould,Aluminum Extrusion Die
Suzhou Remgar Metal Manufacturer Co.,Ltd. , https://www.remgaral.com