1. Internal and external rocker arm gap is too large
(1) Inside and outside the rocker pad gasket
Gasket available sheet metal, copper, iron wire, semi-circular opening pins made of "factory" glyph. During installation, make sure there is a certain gap between the inner and outer rocker arms and wrap the gasket to prevent falling.
(2) test gasket thickness is appropriate
Manually stretch the crankshaft of the engine slowly to the petrol pump mounting hole on the cylinder block, wait for the hand to feel the tip of the driving petrol pump on the cam, and install the petrol pump Install the gas pump and the liner between the cylinder). Install the gasoline pump fastening bolts and screw in a little, by hand to promote the gasoline pump to fit with the cylinder, and then relax, at this time if the suction effect, the gasket is too thick, should be adjusted.
2. Broken arm
When the rocker arm break, can take one of the following methods:
(1) Use a wire or string tied to the petrol pump arm, the other end of the lead to the cab, hand control, the car can only drive at low speed.
(2) If there is a small pulley, the above-mentioned wire or string can be tied to the accelerator pedal through a small pulley and controlled by the foot.
(3) The broken rocker removed, find a choke or throttle pull soft pull tube, so that the hole fully lubricated, the one end is fixed on the hand pump handle, while the other end Fixed in the wiper lever on the appropriate position (Note: pull tube should be fixed in the body of the appropriate position). Use, open the wiper switch, the use of wiper lever swing back and forth so that the pump constantly pumping oil.
(4) For electric wiper models, the electric wiper assembly can be removed, fixed to the gasoline pump at the top of the appropriate position, with the ends of the wire were fixed on the handle and wiper lever in the appropriate position . Take a good wiper power supply, you can use the electric wiper lever swing back and forth to bring hand crank pump oil.
The above several methods of choice, according to the specific conditions at the time decision.
3. Pump membrane ruptured
(1) For the pump membrane with less serious damage, for example, only the edge is damaged, deep damaged soap can be separated from damaged pump membrane and good pump membrane, Pack complex.
(2) If the pump membrane cracks longer, available plastic, tarpaulin, film cut into the original shape of the film, sandwiched between the original film.
(3) If gasoline is found to flow into the crankcase from the rupture of the pump membrane, the crankcase oil is severely diluted. Should be replaced with new oil. If there is no new oil, the old oil in the crankcase can also be released for heating, so that the old oil can be temporarily used after the gasoline in the oil is evaporated.
4. Into, out of the valve seal is poor
(1) If the bakelite oil valve is not flat, the valve can be turned over to continue to use, or the uneven side of the oil surface grinding, it is best to use abrasive paste on the glass polished. Good grinding of the valve can be installed before use.
(2) If the inlet and outlet valves are poorly sealed due to gumming, the jelly may be washed off with alcohol or high-concentration white spirit or acetone.
(3) If the oil valve has ruptured, replace it with a thinner piece of glass.
The method of making is to immerse the glass in water and clamp the glass piece slowly into the shape of the oil valve with pliers.
5. Oil cup ruptured
(1) If the grease cup is only cracked, it can be repaired with old plastic (such as a toothbrush handle). First, the oil cup rupture thoroughly clean, the plastic on the exhaust pipe heating (be careful not to plastic stained with oil), to be melted quickly press the crack in the cup, and let it adhere to a certain Thickness, with the exhaust pipe on the heater in advance will repair the Department by pressing the flat, so that the bond more firmly.
(2) If the oil cup is broken, replace it with a substitute. Many types of substitutes, such as bottles, small thermos cover, beverage boxes, bamboo, small cups, flashlight caps, cream bottles and so on. If the substitutes are not high enough to be fixed, a padding pad 2 may be placed on the bottom of the substitutes. The thickness of the spacer should be fixed firmly by using the screws as a substitute.
If you choose the bottle as a substitute, the processing methods are as follows: with a cotton-stained cotton thread wrapped around the bottle to be cut off, and then ignite the cotton thread, when the cotton is almost ready to be burned, quickly into the cold water. As the bottle collapses rapidly due to the cold, the bottle is disconnected at the winding.
If the broken oil cup with a partition structure in the middle, the soft board can be processed into the shape and size of the original partition, and according to the installation position of the original partition can be placed.
6. Outer arm and cam worn too
If the external rocker arm and cam worn over even the fuel pump is too small, you can thin the gas pump and cylinder liner liner or even removed (but can not leak oil from here).
7. Pump spring break
If the pump membrane spring break, the steering wheel can be used to replace the electric horn button springs on the steering shaft or other similar springs.
8. Gas leaks
(1) If the liner can not withstand the sealing effect due to stiffness, the liner can be soaked in hot water, softened and then coated with grease to continue to re-use.
(2) If the above method still can not be used or the liner has ruptured, it can be processed according to the original liner size, such as yellow board paper or asbestos board.
9. Gas pump produces "gas resistance" phenomenon
Gas pump "gas resistance" to eliminate as follows:
(1) stop the engine, open the hood for ventilation;
(2) Rinse the tubing with cold water to help cool (but not to the intake and exhaust pipes and petrol pump water cup);
(3) Use cotton or rag soaked in cold water and put it on the gasoline pump for cooling. After a period of time, remove the carburetor into the oil pipe and pump the oil several times by hand (be careful not to pump the oil to the engine);
(4) Ruoyin temperature is too high, frequent occurrence of gas resistance, can be made of sandbags, soaked in water on the pump above to cut off the exhaust pipe to the radiant heat pump. In order to improve the insulation effect of sandbags, we should often use cold water soaked.
10. Gas pump damaged
If the pump damage is not working properly, the following method can be taken to replace the role of gasoline pump: a container filled with gasoline, installed in the position above the carburetor, the tubing with the carburetor to connect the container to form Self-flow fuel supply.
Pay attention to fire prevention when using this method.