Xigong Chu Sheng Vacuum Sewage Cart Selection and Working Principle


Xiagong Chusheng (Hubei) Special Purpose Vehicle Co., Ltd. vacuum suction truck is a new type of sanitation vehicle that collects, transfers, cleans up the transport sludge, sewage, and avoids secondary pollution. The sewage suction truck can be self-priming and self-discharging. With large capacity and convenient transportation, it is suitable for collecting and transporting feces, mud, crude oil and other liquid substances. Sewage suction truck adopts the domestic leading vacuum pump for suction pump, which has large suction and long suction range. It is particularly suitable for the suction, shipment and discharge of sludge in the sewer, especially for the suction of sewer mud, silt, stones and bricks. Blocks and other larger objects.

First, the purchase of sewage truck

1, pay attention to the quality of the plate, vacuum sealing, poor material can easily cause deformation of the tank and other issues.

2. The choice of vacuum kit, the pressure capacity and the perception of temperature difference. The domestic kit debuts Veyron products.

3, the choice of the rear tank cover, according to the local operating environment, temperature and other choices.

4. According to the relevant regulations of the National Development and Reform Commission on the enforcement of the three-gas emission from the country, the National 2nd vehicle parameter data has been deleted since July 1, 2008. Please pay attention to identifying the country's 3 emissions labels and related procedures when purchasing vehicles.

Second, sewage suction truck operation manual

1. Preparation before operation

(1) The rear part of the sewage suction truck should be as close as possible to the operating point and parked.

(2) Pull the return oil tank's straight cock rotating handle to the angle of about 45° with the axis of the oil inlet pipe. Observe the oil inlet pipe and there should be lubricating oil flow.

(3) Open the side door of the walk-in box and take out the dirt-absorbing rubber hose so that it swings back without bending.

2. Pumping operation

(1). Draw the sewage suction hose as deep as possible to ensure that the end of the pipe is 300mm below the liquid level during the operation.

(2) Push the four-way valve handle vertically to the ground.

(3). Hitch the transmission to neutral, then start the engine, disconnect the clutch, pull the power take-off switch backwards to pull the file, and the vacuum pump starts to run.

(4) Open the cabin tool box, pull out the alarm switch, and turn it on.

(5) The operator can pass through the observation mirror on the upper part of the rear head. When the liquid level reaches the middle of the observation mirror, the operator should be notified that the colleague should quickly pull the suction hose away from the ground or close the four-way valve. Under normal circumstances, the sounder will emit audible and visual signals at this time. When the driver receives the signal, the throttle should be reduced. The power take-off switch is pushed forward and the gear is removed. The vacuum pump stops moving and presses the switch to cut off the power. .

(6) Close the fuel tank straight cock rotating handle plate parallel to the axis of the incoming mailbox.

(7) After flushing the hose, place it back in the walkway box, close the side door, and position the boom over the cab.

(8) Close the anti-overflow valve so that the handle is perpendicular to the axis of the road.

(9) Drive the sewer truck away from the operating point.

3. Drainage operations

(1) Point the suction hose toward the reservoir.

(2) Pull the rear handle of the four-way valve parallel to the ground and open the spill-proof valve so that the handle and the pipe axis can be parallel.

(3) Hitch the transmission to neutral, then start the engine, disconnect the clutch, pull the power take-off switch backwards to pull the file, take the power, start the vacuum pump, put the transmission into neutral, then start the engine, separate the clutch, and take the power. The switch pulls back and pulls the file, and the vacuum pump starts to operate.

(4) After the discharge of the liquid in the tank, the driver should push the power take-off handle forward and remove the gear, and the vacuum pump stops running.

(5) Close the fuel tank straight cock rotating handle plate and enter the axis of the e-mail box and close it. After the hose is rinsed, put it back into the walk-in box, close the side door, and make the suspender point towards the cab.

(6) Move the sewer truck away from the operating point.

Nodulizer

Type: Ferro Silicon Magnesium, Rare earth Ferro Silicon Magnesium Size: 1-6mm, 2-12mm, 5-30mm or as per demand

Packing: 25kgs waterproof bags inside 1mt big bag or as per demand

Application: The raw materials used in the production of the nodulizer are all deoxidized and de-rusted, and are produced through special smelting equipment, The melting of the alloys is carried out in a protective atmosphere so that the MgO content in the nodulizer is extremely low, and the MgO content in the RE Mg nodularizer can be stably controlled below 0.8%, or MgO content controlled below 0.5% according to customer demand. The MgO content in nickel-magnesium and copper-magnesium alloy nodulizer can be controlled at 2.5% or less.

Nodulizer

Nodulizer For Casting,Foundry Nodulizer,Casting Nodulizer,Smelting Nodularizer

Shijiazhuang BKDR Metallurgical Science & Technology Co.,Ltd , http://www.bkdrtech.com